-
Q What are included in one set breaker?
A Standard package include two chisels, two hoses, one set of N2 charging kit with N2 bottle and pressure gauage, one set of spare seal kit, one tool box with necessary maintenance tools and operation manual as well.
-
Q Can the earth drill fit a variety of machines?
A Yes, as long as the machine specifications fall within the parameters of the Earth Drill as outlined in the product information.
-
Q What is the use of the auger?
A An auger is a rotating metal shaft with blades that circle the outside edge.
The blades are designed to clear away and pull out material from the hole you are digging.
The auger has many uses, which may include:
1.Fence Post Hole Drilling
2.Building Foundations
3.Planting Trees 4.Deck Footings
-
Q How to operate the excavator auger?
A Here is a few tips for fitting the auger drive and auger to the mini excavator...
1.Lay the auger drive down with hose faces away from you.
2.Remove the bucket from the excavator if fitted.
3.Hook up the auger drive mount to excavator hitch and fit pin.
4.Connect up the hydraulics, have a rag handy to clean connections.
5.Connect the auger bit to the auger drive and fit pin 6.Use the toggle switch or foot pedal to control the auger.
-
Q What is an auger attachment for a skid steer?
A A skid steer auger is an attachment designed to pierce the ground and drill straight down. In doing so, this attachment proves useful in a wide range of applications.
-
Q How deep can you auger with a skid steer?
A Depth: Most auger drill bits have a dig depth of up to 72 inches. However, the actual dig depth depends on the model of skid steer you're using. Extension attachments are available to increase dig depth if necessary.
-
Q How much does an auger for a skid steer cost?
A It can range from $1500to $3000 per piece.
-
Q How deep can a towable auger dig?
A You can add an extension rod to the auger.
-
Q What is a hydraulic auger?
A A hydraulic auger is a powered drill that uses fluid pressure to operate. The hydraulic auger serves the same purpose as a drill machine but with much more power and speed. Some models can rotate up to 19 revolutions per minute!
-
Q Should you wet gravel before compacting?
A Should I wet gravel before compacting? You don't necessarily need to wet gravel before compacting, however a light amount of water can help to keep dust levels down. Just be sure not to make the area too wet.
-
Q How heavy of a plate compactor do I need?
A A rule of thumb is that a compactor will compact 1 inch of material for every 1,000 pounds of compaction force it exerts. You should also consider the machine's vibration frequency, measured in vibrations per minute. Higher vibration frequency (around 5,700 vpm) is good for compounding thin layers of material.
-
Q What is the difference between a rammer and a plate compactor?
A Rammers have the ability to compact a deeper amount of soil than a plate compactor, because the force from the plate is more direct. Therefore, more soil can be added to each layer which can make the process of filling and compacting a hole or trench, much faster.
-
Q Which is better jumping jack or plate compactor?
A Having Both. While vibrating plate compactors are best for larger areas and granular soils, jack rammers are an excellent choice for mixed or cohesive soil and smaller areas or trenches.
-
Q What are the four common types of compaction equipment?
A The method of compaction is primarily of four types such as kneading, static, dynamic or impact and vibratory compaction. Different type of action is effective in different type of soils such as for cohesive soils; sheepsfoot rollers or pneumatic rollers provide the kneading action.
-
Q What is compactor used for?
A A compactor is a machine or mechanism used to reduce the size of material such as waste material or bio mass through compaction. A trash compactor is often used by a home or business to reduce the volume of trash it produces.
-
Q How many tons of excavator are used for?
A 1-40T excavator with different brands.
-
Q How does a hydraulic compactor work?
A The hydraulic compactor compresses materials with hydraulic pressure. The hydraulic system works by placing a liquid under great pressure in order to transmit power.
-
Q How much horsepower does it take to pull a ripper?
A In some areas we use one pass, in corn stalks we usually do two or three passes. The guys using the v-rippers need 450 horsepower to pull them. I get the depth without that power.
-
Q How deep should you run a ripper?
A Deep ripping mechanically breaks up compacted soil layers, but care must be taken to ensure that the results are effective. Deep ripping uses strong tines working up to 35-50cm deep to loosen tough soil layers.
-
Q What is a ripper tooth?
A A ripper tooth is an attachment that is mounted on an excavator and used to break up rock and very hard soil. The design of this attachment means it is a very strong tool for the job, capable of digging; or rip, even the toughest floors