Leading Earth Auger Manufacturer in China Since 2002

Yes, as long as the machine specifications fall within the parameters of the Earth Drill as outlined in the product information.

An auger is a rotating metal shaft with blades that circle the outside edge.
The blades are designed to clear away and pull out material from the hole you are digging.
The auger has many uses, which may include:
1.Fence Post Hole Drilling
2.Building Foundations
3.Planting Trees 4.Deck Footings

Here is a few tips for fitting the auger drive and auger to the mini excavator...
1.Lay the auger drive down with hose faces away from you.
2.Remove the bucket from the excavator if fitted.
3.Hook up the auger drive mount to excavator hitch and fit pin.
4.Connect up the hydraulics, have a rag handy to clean connections.
5.Connect the auger bit to the auger drive and fit pin 6.Use the toggle switch or foot pedal to control the auger.

A skid steer auger is an attachment designed to pierce the ground and drill straight down. In doing so, this attachment proves useful in a wide range of applications.

Depth: Most auger drill bits have a dig depth of up to 72 inches. However, the actual dig depth depends on the model of skid steer you're using. Extension attachments are available to increase dig depth if necessary.

It can range from $1500to $3000 per piece.

You can add an extension rod to the auger.

A hydraulic auger is a powered drill that uses fluid pressure to operate. The hydraulic auger serves the same purpose as a drill machine but with much more power and speed. Some models can rotate up to 19 revolutions per minute!

1. It is much cheaper than buying a dedicated stump grinder or a stump grinder attachment for skid steer loaders. 2. Use the equipment you already have to expand your current capabilities. 3. Quickly save money by doing it yourself instead of hiring a tree service to do it for you, plus you'll always have the attachment for future use when you need it again. Incorporates 3 cutting blades and a starter tip. 4. The cutting blades and starter tips can be sharpened and/or replaced as needed, so you can count on a long service life from this tool. 5. The starter tip guides the planer through the stump, while guides on the edge of the blade prevent the attachment from jumping off the stump. 6. This clever design allows the brushcutter to drill up to 18" into the stump and soil, ensuring that your stump will be permanently removed. 7. Traditional stump grinders are not capable of going as deep as this tool, so they are not as effective for stump removal.

We use uniform non-fumigated wooden boxes. and we wrap them with film so that they do not get dirty easily.

The 12" stump planing auger requires an earth auger drive unit that can produce at least 3,000 foot-pounds of torque and the 16" requires an earth auger drive unit that can produce at least 5,500 foot-pounds of torque. Our stump planer augers are also not compatible with 3 Point PTO Augers for tractors.We would recommend that the 12" diameter stump auger bit would be best suited on most standard flow drive units. The big 16" stump auger bit would be best matched up to one of the many high torque drive units we produce. Either of these sizes would be a great match to one of our two speed drive units as well.

By adding this stump auger bit to your arsenal of attachments you can safely grind stumps down without the mess, noise and danger that a conventional stump grinder produces.

1) Disassembly. Follow the disassembly procedure in the product manual. 2) Grinding. Using a bench grinder fitted with a “Green” Silicone Carbide, make several small passes against the cutting face ensuring that the cutting edge angle is maintained at 50 degrees.

3pcs blades

There are several ways to remove tree stumps from your yard, including manual labour, chemicals and burning. You can also rent a stump planer or make it easy on yourself, albeit at a cost, by hiring a professional to do the job.

The stump planer from RAY Attachments is designed to grind stumps safely, without mess and without noise. The drill is available in 12" (250mm) and 16" (300mm) diameters. The company recommends the 12" size for standard flow drives and the 16" for one of the company's high-torque drives.

We are a manufacturer. We have over 19 years of experience in manufacturing skid steers and skid steers. It is the top producer and exporter in the industry.

Ordinarily, it costs 20-25 workdays for 2x40ft containers. Sample order in 5 days.

Payment≤20000USD,100% in advance. Payment＞20000USD, 30% T/T in advance, balance after production completed. Or LC at sight.

Raw material inspection-checking drawing before production-inspect the actual size according to drawing-finished product inspection- testing report-package inspection-qualified certification.